Learn
Plain answers to the questions people ask about EQ, mixing and making music, with the product shown doing it.
EQ
-
What EQ does in music
EQ, short for equalization, turns one range of frequencies up or down inside a sound: less boom in a kick, less box in a pad, more air on a vocal. It changes the balance inside a sound, not its loudness, so that when sounds play together each one is heard.
-
How to EQ: the method
One order for any sound: listen in the mix, cut what does not belong, find the one bad spot with a narrow sweep and cut it, then lift broadly and last. Three bands is normal, small moves are the rule, and a bypass check at matched level is the proof. Shown on a pad in a small digital mix.
-
How to EQ vocals
Four moves: cut below 90 Hz, find the room's boom or the box with a sweep and cut it, let a dynamic band tame the esses only when they hit, and add a little air last. Leave the middle alone, because 300 Hz to 3 kHz is the voice. Shown on a sung line in a small digital mix.
-
How to EQ a kick drum
Pick the sample first. Then cut below the kick's note, find and cut the shell's ring between 300 and 500 Hz, give the kick its weight where the bass is not, and lift the click near 4 kHz so a phone hears it. Four moves, each shown in the plugin on one loop.
-
How to EQ a snare
A snare has four parts: a thump under 100 Hz many samples carry, the body between 150 and 250 Hz, a ring between 400 Hz and 1 kHz, and the crack between 2 and 5 kHz. Cut the thump, find the ring with a sweep and cut it narrow, lift the body a touch, and lift the crack so a phone hears the hit.
-
How to EQ drums
EQ a drum loop or a kit's bus in four moves: cut below 30 Hz, find the kit's box between 300 and 500 Hz and cut it, tame the hats' harshness with a dynamic band near 4 kHz, and add air last. The kick and the snare get their own pages; this is the beat as one sound.
-
How to EQ guitar
Most guitar EQ is taking away what the amp added: cut below 100 Hz where the bass lives, find the mud between 200 and 400 Hz and cut it, tame the amp's fizz above 5 kHz, and make a small room for the vocal near 2.5 kHz. Leave 800 Hz to 2 kHz alone, because that is the guitar.
-
How to EQ bass
Bass and kick share the lowest octave, so decide who owns it first. Four moves: duck the bass under the kick with a dynamic band keyed from the kick, cut below the note gently or not at all, cut the mud between 200 and 300 Hz, and lift the harmonics near 1 kHz so a phone hears the line.
-
How to EQ piano
A piano covers the whole range, so EQ it for the mix around it: cut below 60 Hz when a bass plays, cut the boom between 200 and 300 Hz when it clouds the mix, take the hardness near 3 kHz down a touch when the hammers bite, and add air last. The middle is the piano: leave 400 Hz to 2 kHz alone.
-
Mid/side EQ explained
Mid/side EQ splits a stereo sound into its centre and its width and lets a band act on one: a low cut on the sides keeps the kick and the bass in the middle, a lift on the sides adds air without touching the vocal. In Neutral EQ any band can be placed on the mid, side, left or right.
-
Linear phase EQ: when to use it
An ordinary EQ shifts the timing of the frequencies it touches a little; a linear phase EQ does not, at the cost of latency and a faint ring before sharp hits. Use it where timing matters: a steep cut near a kick's note, a master, two paths of one sound summed. The ordinary kind everywhere else.
-
Dynamic EQ explained
A dynamic EQ is an EQ band that moves by itself: it cuts or lifts only while the sound is too loud in that one range, and lets go when it is not. Use it for a problem that comes and goes, like a sharp ess, one boomy note, or a bass that should dip only while the kick hits.